Alat Uji Material


Ultrasonic Thickness Gauge BGTM-8812
1. ultrasonic thickness gauge BGTM-8812Untuk mengukur ketebalan besi, kaca, plastik, dll, sampai ketebalan 20  cm
SPECIFICATIONS:
*Measuring frequency: 5MHz
*Measuring range: 1.20 – 200 mm or 0.047 – 7.874 inch (steel)
*Accuracy: +/- (0.5%H ± 0.1) mm
*Sound velocity range: 500 – 9,000 m/s
*Resolution: 0.1mm or 0.001 inch
*Working temperature: 0 ºC ~ +50 ºC
*Size: 120mm x 62mm x 30mm
*Power supply: Battery 4 x AAA alkaline batteries (6.0V)
*Weight: ±200g


Ultrasonic Thickness Gauge BG-2300
2. ultrasonic thickness gauge BG-2300Untuk mengukur ketebalan besi, kaca, plastik, dll, sampai ketebalan 22  cm
SPECIFICATIONS:
*Work Frekwency : 5 Mhz
*Measuring Range : 1.2mm to 220 mm on steel
*Minimum Limit tube measuring : 120 x 3 mm steel
*Accuracy : 1% + 0.1mm
*Sound velocity range : 1, 000 to 9, 999 m/ s
*Power Supply : 3 x 1.5Volt AAA Battery
*Size : 70.0 x 145 x 28mm
*Weight : 210g


Vibration Meter VM-6360
3. vibration meter VM-6360Untuk mengukur getaran pada mesin, pompa, pipa, dll, sampai dengan 400 m/s²
SPECIFICATIONS:
*Acceleration (Peak value): 10Hz to 1KHz:   20.1-400m/S²; 10Hz to 10KHz:   0.3-1312 ft/S²
*Velocity (RMS): 10Hz to 1KHz:  0.1-400(mm/s)  ;  0.004-16.0 inch/s
*Displacement (Peak to peak): 10Hz to 1KHz:  0.001-4.0 (mm) ;  0.04 – 160 mil
*RPM (Revolution): 5-100,000r/min
*Frequency: 0.1 to 10KHz
*Accuracy: <5%+2


Vibration Meter VM-6370
4. vibration meter VM-6370Untuk mengukur getaran pada motor, pompa, bearing, pipa, tanki, dinding, dll
SPECIFICATIONS:
*Velocity: 0.01-400.0 mm/s 0.000-16.00 inch/s true RMS
*Acceleration: 0.1-400.0 m/s² 0.3-1312 ft/s²
*Displacement:0.001-4.000mm 0.04-160.0 mil
*Frequency Range for Measuring:10Hz. to 10kHz.
*Accuracy:5% of reading + 2 digits
*Temperature : 0-50 ℃
*Humidity : below 95% RH


Film/Coating Thickness Gauge BG-2131
5. film coating thickness gauge BG-2131Untuk mengukur ketebalan Cat pada permukaan plat
SPECIFICATIONS:
*Measuring range 0~ 1800µ m
*Accuracy ±  3% H± 1µ m
*Resolution: 0.1µ m ( 100µ m)
*Use Hi-sensibility sensor for precise measurement
*Zero point, two point and basic, three different calibration
*Measuring mode: Single, Continually and Difference
*Data store/ Data recall/ Data delete function
*Data Analysis: Average, Maximum, Minimum, Standard deviation and measuring times
*Beep sound indication
*Measure in Metric/ Imperial
*LCD backlight display
*Low battery indication
*Auto power off
*Power supply: 9V battery
*Weight: 147g ( without battery)
*Dimension: 67* 30* 183mm


Elcometer 456 Coating thickness
6. elcometer 456 coating thickness gaugeUntuk mengukur ketebalan cat pada permukaan plat (Ferros dan Non-Ferros)
Specification:
*Range: 0-1500µm (0-60mils)
*Resolution: 0.1µm: 0-100µm; 1µm: 100-1500µm (0.01mil: 0-5mils; 0.1mil: 5-60mils)


Dial Gauge Peacok Model G (Made in Japan)
7. dial gauge peacock model GUntuk mengukur ketebalan plastik, kertas, sampai dengan 10mm
SPECIFICATIONS:
*Range: 10 mm x 0.01mm


Durometer Kori KR-14A
8. durometer kori KR-14AUntuk mengukur kekerasan dari bahan karet (Shore-A)
SPECIFICATIONS:
Model KR-14A Standard
Purpose : General Rubber
Applied Standard : JIS 6253 , ISO 7619 , ASTM D2240
Test Load : 550-8, 050 mN ( 56.1-821.1gf )


Durometer Tecklock GS-702G
9. durometer tecklock GS-702GUntuk mengukur kekerasan bahan dengan Shore D seperti plastik dan karet keras
SPECIFICATIONS:
*Model: GS-702G
*Type: D
*Applicatioin: Plastic/Hard Rubber
*Applicable Standards: JIS K 7215
*Spring Load Hardness 0-100: 0-44483mN, 0-4536gf
*Indenter Shape: RO.1 with 30˚ angle, conical cone
*Indenter Height (mm): 2.50
*Weight: 208


Digital Calipers Kori  (Made in Japan)
10. digital caliper Kori made in JapanUntuk mengukur ketebalan material dari plastik, kertas sampai 15mm
SPECIFICATIONS:
*Resolution: 0.01mm, 0.0005″
*Measuring range: 0 – 15mm / 0 – 0.6″
*Error of indication: below 0.03mm
*Throat depth: 35mm
*Power: one 1.55V (SR44) button cell, which last 8 – 12 months. The digits will twinkle when the power is used up. Then battery must be replaced
*Working temperature: 0 – 40˚C
*Storage temperature: -10˚C to 60˚C
*Relative humidity: <80%


Infrared Thermometer BE-550 (Best One)
11. infrared thermometer BE-550Alat untuk mengukur suhu suatu benda dengan sinar laser
SPECIFICATIONS:
*Temperature range: -50~ 550° C (-58~ 1022° F)
*Accuracy: ± 1.5% or ± 1.5° C
*Repeatability: 1% of reading or 1° C
*Distance Spot Ratio: 12: 1
*Emissivity: 0.95 preset
*Resolution: 0.1° C/ ° F
*Wavelength: 8-14µm


Fruit Sclerometer (GY-3 Series Analog)
12. fruit sclerometer GY-3Untuk mengukur kekerasan dari buah
SPECIFICATIONS:
*Capacity: 0.5 – 12 kg/cm² ; 1-24 kg/cm²
*Resolution: 0.1 kg/cm² ; 0.2 kg/cm²
*Pressure Diameter: 1#ɸ 11.1 mm ; 2#ɸ 7.9mm
*Accuracy: ±2%
*Display: analog / dial
*Dimension: L150 x W55 x H30 (mm)
*Tip Depth: 10mm
*Weight: 0.3 kg


Paper Moisute Content Tester (Paper Moisture Meter) BG-03
13. paper moisture meter BG-03Untuk mengukur kelembaban dari bahan kertas
SPECIFICATIONS:
*Display: 2 digit LCD and the character height is 15mm
*Sampling speed: 3 times/sec
*Resolution: 1%
*Measuring range: 5% – 40%
*Accuracy: ±1% rdg + 1d
*Working environment: 0 – 40˚C (0 – 70% RH)
*Storage evironment: -10 to 50˚C ( 0 – 85% RH)
*Power: 9V Type 6F22
*Dimension: 150 x 70 x 30mm (LxWxH)
*Weight: about 137g


Kontak Person

BINTANG GLOBAL TEKNIK
Address : Lindeteves Trade Centre (LTC)Lantai 2 Blok C3 No 6-7
Jl. Hayam Wuruk No. 127, Glodok, Jakarta
Website : www.karyamitra.co.id
E-Mail :
bgt222444888@yahoo.com
Telepon :
021-30063681 (Hunting)
Faximile : 021-62320340
Handphone :
0812 1224 3600 Christian